Time for a new board

What works & what doesn't and in what type of conditions. Got a "secret" only you and your shaper know???? Post it here... we can keep it quiet ;-)

Moderator: Moderator

coelacanth
Grom (25 or less posts to site)
Grom (25 or less posts to site)
Posts: 24
Joined: Mon Jul 17, 2006 4:16 pm
Location: Huntington Beach

Re: Time for a new board

Post by coelacanth »

I never thought I would make this many boards, so I never felt like learning how to install a removable system. I retrospect, it would probably been a good choice financially since I could use the same fins for different boards (fins sets can cost as much or more than the blank). I was also concerned that if I screwed up the installation of the plugs/boxes, I would really be screwed. With glass-ons, you can grind them off and reposition (although I have only done this for a board someone else shaped). One more sad fact - with my boards, if there's something wrong with the board, changing the fins is not going to fix the problem. Regarding the choice of foam density in the blank, I just get what's in stock at the supplier (usually the red). And yes, they do get dinged up. Putting in the deck patches has helped. Not eating it as often would help even more.
Hot coating the deck
Hot coating the deck
Not extinct
User avatar
joe
Legend (Contribution King!)
Legend (Contribution King!)
Posts: 793
Joined: Thu Dec 04, 2003 5:28 pm
Location: San Diego

Re: Time for a new board

Post by joe »

Thanks for sharing your board build. I'm very impressed. Good job.
coelacanth
Grom (25 or less posts to site)
Grom (25 or less posts to site)
Posts: 24
Joined: Mon Jul 17, 2006 4:16 pm
Location: Huntington Beach

Re: Time for a new board

Post by coelacanth »

Finally finished, Hasn't been in the water yet. Soon.
Using template to cut the knee pad
Using template to cut the knee pad
DPK7-24.jpg
DPK7-25.jpg
Not extinct
coelacanth
Grom (25 or less posts to site)
Grom (25 or less posts to site)
Posts: 24
Joined: Mon Jul 17, 2006 4:16 pm
Location: Huntington Beach

Re: Time for a new board

Post by coelacanth »

Logos
DPK7-26.jpg
DPK7-27.jpg
Not extinct
User avatar
southpeakbrad
Legend (Contribution King!)
Legend (Contribution King!)
Posts: 872
Joined: Fri Nov 28, 2003 3:42 pm
Location: San Diego

Re: Time for a new board

Post by southpeakbrad »

Thanks! Looks great...hope it goes well. We're waiting for the report 8)
Josh Peters
Local (More than 25 post)
Local (More than 25 post)
Posts: 30
Joined: Mon May 20, 2013 8:30 pm

Re: Time for a new board

Post by Josh Peters »

the deck pad looks great. The hole board looks great can't wait to here how it surfs. all your hard work will be worth it.
Josh Peters
coelacanth
Grom (25 or less posts to site)
Grom (25 or less posts to site)
Posts: 24
Joined: Mon Jul 17, 2006 4:16 pm
Location: Huntington Beach

Re: Time for a new board

Post by coelacanth »

Only had the board out a few times (some family issues have reduced my surf time for the last several weeks). Paddles and catches waves fine and overall balance feels pretty good. I bit of weirdness in a few circumstances, hopefully things I can figure out as I get used to the board and ride it in different (i.e. better) conditions.
Not extinct
User avatar
thebagman
Grom (25 or less posts to site)
Grom (25 or less posts to site)
Posts: 12
Joined: Fri May 06, 2016 3:43 am
Location: North SD County CA

Re: Time for a new board

Post by thebagman »

Sorry for the late post, I have to agree with brad on the fins and foam, recommend routering out the deck area where your knees are and use a sheet of divinycell if your going to use red. Just from my experience. Also a sheet of carbon 2x2 over that and your board will be almost impervious to the pressure dings. Here's one of my suppliers for aircraft stuff.
http://www.fibreglast.com/category/Foam
http://www.fibreglast.com/product/vinyl ... nsity/Foam
Plastics Technology Graduate 1974
Sunset Cliffs Kneeboarder 1970's
Steve Lis Apprentice
Post Reply